You are here: Auto-Feed Riveting Gun Guide: Types, Sizes, Selection and Fixes
Blind rivets (commonly called pop rivets) are the most widely used single-side fastener in enclosures and cabinets, sheet metal fabrication, appliances and auto parts, and the auto-feed riveting gun is the equipment built to sort, feed and set them. In real support calls, a large share of failures and bad selections trace back to a misunderstanding of the rivet itself. This guide brings the types, sizes, selection rules and field problems together in one place, so buyers, process engineers and maintenance teams can work from the same reference.
One order covers the equipment and the consumables, so the line does not stop waiting for a second shipment. The notes below cover auto-feed riveting gun supply and procurement.
For buyers who source machines, rivets and spare parts in one order, the essentials: how a blind rivet works; what types of blind rivets are there?; open-End vs closed-end blind rivets; blind rivets vs semi-tubular rivets.
1. How a Blind Rivet Works
A blind rivet has two parts: the body (rivet body) and the mandrel (stem). To set it, the high-force automatic rivet gun grips the mandrel and pulls it back; the blind end of the body expands into a setting head that clamps two or more sheets together, and when the pull force reaches the set point the mandrel snaps at the break groove, completing the joint from one side. Because you only work from one side of the part, boxes, tubes and closed cavities with no rear access are all usable, which is the biggest efficiency advantage a blind rivet holds over solid rivets and bolted joints.
2. What Types of Blind Rivets Are There?
| Category | Type | Features / use |
|---|---|---|
| Body structure | Open-end | Most common and lowest cost; the body stays open at the tail after the mandrel breaks, for standard enclosure sheet metal |
| Closed-end | Body sealed at the tail; water- and moisture-proof after setting, for outdoor, rain-exposed and sealed assemblies | |
| Head shape | Dome head (button head) | Standard type with a large clamping area; use where a raised head is acceptable |
| Countersunk head | Flush with the panel after setting; used on visible faces and rail surfaces | |
| Function | Multi-drum (double drum) | Forms several bulges that spread the clamping load; suited to thin sheet and soft materials |
| Structural (high-strength) | Mandrel locks in place and cannot work loose; vibration-resistant with high clamp load, common in automotive and EV work | |
| Grooved (wide-grip) | Large grip range for mixed thick and thin stacks and multi-layer holes | |
| Material | Aluminum/steel, all-aluminum, all-steel, stainless steel, copper | Choose by strength, corrosion resistance and electrochemical compatibility |
A single supplier shortens the approval cycle for both the machine and the consumables.
3. Open-End vs Closed-End Blind Rivets
| Item | Open-end | Closed-end |
|---|---|---|
| Structure | Hollow body, open at the tail | Body sealed into a dome at the tail |
| Water resistance | No sealing | Seals on setting and keeps rainwater out |
| Mandrel retention | The broken mandrel can work loose and drop out | The broken mandrel stays trapped inside the sealed end |
| Cost | Low | Higher |
| Typical use | Indoor enclosures and cabinets, appliance internals | Outdoor cabinets, lighting, vehicles, damp kitchen and bathroom environments |
4. Blind Rivets vs Semi-Tubular Rivets
| Item | Blind rivet | Semi-tubular rivet |
|---|---|---|
| Setting method | Single-side pull with a high-force automatic rivet gun; the mandrel forms the head | Two-sided operation; a punch or spinning head rolls the hollow end over |
| Equipment | Auto-Feed Riveting Gun / high-force automatic rivet gun | Spinning riveter, press riveter and similar |
| Access | One side only; works on closed cavities | Needs support or a die on the back side |
| Typical application | Enclosures and cabinets, sheet metal boxes, appliance shells | Hardware, luggage, hinges, small precision parts |
The two are not substitutes for each other; you choose by part structure and rear-side access. An auto-feed riveting gun only handles blind rivets, while semi-tubular rivets need spinning or press riveting equipment, so confirm the process route before you buy and avoid ordering the wrong machine type.
Price per rivet, not price per machine, is the number that survives the first year.
5. How to Choose Blind Rivets: Four Key Factors for Your Auto-Feed Riveting Gun
First, grip thickness (grip range): the body length has to cover the total stack thickness. Too short and the joint will not hold, too long and the head forms badly, and every catalog page lists the grip range for that part number. Second, hole diameter match: a standard hole usually runs 0.1-0.2 mm larger than the rivet diameter. Too large and the joint works loose, too small and the body will not go in. Third, material pairing: generally match the body to the workpiece material to avoid galvanic corrosion, and put stainless rivets in stainless parts. Fourth, strength and appearance: structural types where vibration is high, countersunk heads on visible faces, closed-end types outdoors. Hand these parameters to the equipment builder together with physical sample rivets, and they can match the right nosepiece and feed track (see can an auto-feed riveting gun run every rivet size).
6. Common Blind Rivet Problems, Causes and Prevention
| Symptom | Common cause | Prevention / fix |
|---|---|---|
| Mandrel will not break | Wrong nosepiece, low air pressure, off-spec rivet hardness | Check the nosepiece specification, hold air pressure at spec, switch to a qualified rivet lot |
| Loose joint that spins | Rivet too short, hole too large, not enough pull force | Size the length to the material thickness, control hole diameter, verify machine pull force |
| Panel pulled through or dented | Nose tip not flat on the panel, dome head used in a countersunk hole, pull force too high | Hold the nosepiece flat on the panel, match head type to hole type, adjust pull force |
| Jammed or short-fed rivet | Burs or deformed rivets, feed track not matched to the size, dirty feed tube | Screen incoming rivet quality, change the nosepiece and clean the track with every size change, clean on a schedule |
| Broken mandrel rattles loose | Open-end mandrel not retained and drops into the cavity | Use closed-end or structural rivets in sealed cavities and anywhere rattling is not acceptable |
| Corrosion after setting | Mixed aluminum and steel, damp environment | Specify stainless or closed-end rivets, add a sealing step where needed |
Most of what looks like a machine fault on an auto-feed riveting gun turns out to be a rivet size, hole diameter or incoming-material issue. Keep one sample of each reject sorted by symptom, and have the engineer on site during the trial run pin down which step is responsible.
Blind Rivet FAQ
Common Questions About Blind Rivets
Q1: Can an auto-feed riveting gun run rivets from different manufacturers?
In principle yes, as long as the specification matches, but dimensional tolerances and surface finish differ between suppliers and the jam rate can change. Before volume production, run a continuous sample batch with the exact rivet lot you plan to buy.
Q2: How many rivet sizes can one machine handle?
Close sizes can share a machine by changing the nosepiece and adjusting the feed track. If cap diameter, body length or material differ widely, you need several feed tracks or several machines; see what types of auto-feed riveting guns there are.
Q3: Is a rivet nut the same thing as a blind rivet?
No. A rivet nut puts a thread into thin sheet for a screw to go into later, while a blind rivet makes a direct connection. Automotive parts use rivet nuts in volume - see this EV parts riveting case study.
Q4: How do I identify a rivet size quickly?
Measure cap diameter, rivet diameter and body length with calipers, note the material and head type, and send a clear photo of the label and the rivet itself to the supplier. If you are unsure, mail a sample rivet; an engineer measuring the real part is the most reliable route.
Not Sure the Rivet Matches the Machine? Test a Sample
You can book an engineer visit and run a continuous sample batch with your own rivets and workpieces to verify feeding, cycle time and yield. Call +86 13556668682.
Further reading: auto-feed riveting gun buying guide (full article) · rivet size compatibility and selection notes · auto-feed riveting gun selection advice
Auto-Feed Riveting Gun at a glance: 20,000 N pull force, 70 rivets per minute, bulk orders shipped worldwide, one-stop supply of machines, rivets and parts.
Consumables and wear parts are quoted alongside the machine, so the total cost per rivet is visible before the order.
Machines, rivets and parts in one order
Send the equipment list and the annual rivet consumption. We will quote the package, the bulk price and the shipping in one reply.
Previous 
