You are here: Auto-Feed Riveting Gun: Can It Use Your Own High-Force Automatic Rivet Gun
Can Your Own High-Force Automatic Rivet Gun Run on an Auto-Feed Riveting Gun? Feed Unit and Gun Compatibility
Customers often ask whether they can buy only the auto-feed unit and keep using the manual high-force automatic rivet gun they already own. The answer is: sometimes yes, but it has to be verified. An auto-feed riveting gun is not simply a feed unit plus any gun. The gun body and the feed unit must agree on mechanical interface, rivet delivery method, control signals and pull force, or you get rivets that stop short, jams, and mandrels that will not break.
Bulk buyers usually compare total cost per rivet rather than the machine price alone, because consumables and wear parts dominate that number. The notes below cover high-force automatic rivet gun supply and procurement.
For buyers who source machines, rivets and spare parts in one order, the essentials: why the gun and the feed unit have to be matched; what a factory-matched gun and feed unit buys you; what if you really want to keep your existing gun; multi-Gun and multi-size setups.
1. Why the Gun and the Feed Unit Have to Be Matched
| Interface point | Requirement | Result when it does not match |
|---|---|---|
| Mechanical interface | The gun needs a rivet inlet and a mounting point that mate with the feed tube | Rivets cannot enter the nosepiece squarely |
| Rivet delivery | Blow-feed or grip-feed timing must match the singulation cycle of the unit | Missed rivets, double feeds, blocked tube |
| Pull force match | Gun pull force must suit the rivet size and the air pressure at the unit | Mandrel will not break, or the joint is not tight |
| Control interlock | Trigger signal must interlock with feeding and counting | No automatic continuous operation |
Consumables ordered with the equipment avoid a second shipment later.
2. What a Factory-Matched Gun and Feed Unit Buys You
The high-force automatic rivet gun Antec develops with its feed systems is matched to the unit in detail. Nosepiece, feed channel and singulation disc are designed around the same rivet size, continuous sample runs are signed off before shipment, and the complete machine is tested for 30000 consecutive rivets without a jam. Staying with the factory gun also keeps wear parts such as nosepieces, jaws and push pins on cost-price supply for the long term, and leaves one party responsible for after-sales setup instead of the machine builder and the gun maker pointing at each other.
3. What If You Really Want to Keep Your Existing Gun
Work through this sequence: (1) send the brand, model and photos of the gun plus the rivet sizes you currently run; (2) ship the gun to the factory, or arrange an engineer visit, and trial-fit it to the feed unit; (3) run continuous sample batches with your real rivets and check feed success rate, cycle time and joint quality; (4) compare retrofit cost and stability before committing. One caution: many manual guns have no automatic rivet inlet, so the retrofit can cost as much as, or more than, a new gun, and the economics do not work.
Bulk orders are packed together, so the line is not waiting on a partial delivery.
4. Multi-Gun and Multi-Size Setups
Dual-gang dual-gun models and robotic riveting cells demand tighter gun-to-gun consistency, so the usual advice is to take the matched gun set and keep cycle time and pull force identical across both guns. When one feed unit has to run several rivet sizes, change the nosepiece and add feed channels. Customers worldwide can book an engineer visit with the feed unit and gun and verify compatibility on their own workpieces.
5. Wear Parts and Consumables for a Matched Gun Set
| Category | Typical parts | Supply |
|---|---|---|
| Nosepiece / rivet inlet | Matched to the rivet cap diameter | Stocked and supplied at cost price, replaced when the size changes |
| Gripping parts | Jaws, push pin, collet sleeve | Wear parts; keep spares in line with consumption |
| Pneumatic parts | Seals, air fittings | Standard parts, inspect and replace on schedule |
| Feed parts | Singulation disc, channel components, sensors | Non-standard parts supplied to suit the model |
The other benefit of a factory gun set is one wear-part number for everything and a stable supply chain. Order a spare set with the new machine based on how hard your nosepieces wear, and add a little more stock on a high-cycle line, to keep unplanned downtime to a minimum.
Be clear on one point: if you modify the machine yourself, or fit a gun or parts the factory has not confirmed, feed matching and pull force can suffer, and the resulting failures are outside the machine warranty. Antec recommends a compatibility evaluation before you decide to keep an old gun. The evaluation is free of charge, a gun that can be mated gets a written fit conclusion, and we advise against opening up the feed unit or the gun yourself.
For the evaluation, also send the air pressure at your site, the planned position of the feed unit and the working envelope of the gun; those details drive feed tube length and workstation layout. If you do keep the old gun, the factory supplies the connectors and mounting hardware needed for the interface and completes the alignment during on-site installation, so you do not have to machine an adapter yourself.
Gun Compatibility FAQ
Supply Q&A
Do not decide on the price gap alone. A gun that does not match will keep the whole setup from running steadily, and the savings are far smaller than the cost of a stopped line, so a matched gun usually works out cheaper.
It depends on the interface and the rivet delivery protocol. We can confirm only after a trial fit, and where the gun can be mated we issue a clear fit conclusion.
Antec keeps nosepieces, jaws and other wear parts in stock and supplies them at cost price for the long term, so standard parts ship quickly.
The interval depends on rivet material, daily output and maintenance practice, so there is no fixed number of days. During the trial and training our engineers give spare-part advice based on your actual cycle rate, and a part is replaced as soon as inspection shows wear past the limit.
High-Force Automatic Rivet Gun at a glance: 20,000 N pull force, 70 rivets per minute, bulk orders shipped worldwide, one-stop supply of machines, rivets and parts.
Send the annual rivet consumption and the equipment list - the team will quote the whole package in one offer.
One supplier for the whole riveting process
Tell us what you buy today and in what volume. We will consolidate the machines, the consumables and the parts into one offer.
Further reading: Can any rivet size run on an auto-feed riveting gun · A guide to the common types of auto-feed riveting guns · Auto-Feed Riveting Gun product center
Previous 
